Linkage disequilibrium

In population genetics, linkage disequilibrium is the non-random association of alleles at two or more loci, not necessarily on the same chromosome. It is not the same as linkage, which describes the association of two or more loci on a chromosome with limited recombination between them. Linkage disequilibrium describes a situation in which some combinations of alleles or genetic markers occur more or less frequently in a population than would be expected from a random formation of haplotypes from alleles based on their frequencies. Non-random associations between polymorphisms at different loci are measured by the degree of linkage disequilibrium (LD). A comparison of different measures is provided by Devlin & Risch ^[1]

Linkage disequilibrium is generally caused by genetic linkage and the rate of recombination; mutation rate; random drift or non-random mating; and population structure. For example, some organisms may show linkage disequilibrium (such as bacteria) because they reproduce asexually and there is no recombination (r=0) to break down the linkage disequilibrium: D'=(1-r)D.

It may be instructive to study genetic equilibrium, and its application in the Hardy-Weinberg principle.

The International HapMap Project enables the study of LD in human populations online. The Ensembl project integrates HapMap data and such from dbSNP in general with other genetic information.

Additional recommended knowledge

Safe Weighing Range Ensures Accurate Results

Daily Visual Balance Check

What is the Correct Way to Check Repeatability in Balances?

Linkage disequilibrium measure, δ

Formally, if we define pairwise LD, we consider indicator variables on alleles at two loci, say I₁,I₂. We define the LD parameter δ (delta) as:

Here p₁,p₂ denote the marginal allele frequencies at the two loci and h₁₂ denotes the haplotype frequency in the joint distribution of both alleles. Various derivatives of this parameter have been developed. In the genetic literature the wording "two alleles are in LD" usually means to imply . Contrariwise, linkage equilibrium, denotes the case δ = 0.

Linkage disequilibrium measure, D

If inspecting the two loci A and B with two alleles each—a two-locus, two-allele model—the following table denotes the frequencies of each combination:

Note that these are relative frequencies. One can use the above frequencies to determine the frequency of each of the alleles:

if the two loci and the alleles are independent from each other, then one can express the observation A1B1 as "A1 must be found and B1 must be found". The table above lists the frequencies for A₁,p₁, and B₁,q₁, hence the frequency of A₁B₁, x₁₁, equals according to the rules of elementary statistics x₁₁ = p₁ * q₁.

A deviation of the observed frequencies from the expected is referred to as the linkage disequilibrium parameter^[2], and is commonly denoted by a capital D ^[3] as defined by:

The following table illustrates the relationship between the haplotype and allele frequencies and D.

When extending these formula for diploid cells rather than investigating the gametes/haplotypes directly, the laid out principle prevails, the recombination rate between the two loci A and B must be taken into account, though, which is commonly denoted by the letter c.

D is nice to calculate with but has the disadvantage of depending on the frequency of the alleles inspected. This is evident since frequencies are between 0 and 1. There can be no D observed if any locus has an allele frequency 0 or 1 and is maximal when frequencies are at 0.5. Lewontin (1964) suggested normalising D by dividing it with the theoretical maximum for the observed allele frequencies. Thus when When D < 0, .

D_max is given by the smaller of p₁q₂ and p₂q₁. D_min is given by the larger of − p₁q₁ and − p₂q₂

Another value is the correlation coefficient as also laid out in the initial paragraphs of this page, denoted as . This however is not adjusted to the loci having different allele frequencies. If it was, r, the square root of r² if given the sign of D would be equivalent to D' ^[4]

Another statistic used in a selective neutrality test is Tajima's D, to decide whether the mean number of differences between pairs of DNA sequences is compatible with the observed number of segregating sites in a sample.

These are summary statistics (i.e. descriptive statistics summarizing the pattern of genetic diversity) that are computed from diploid samples of DNA sequences and which assume that the gametic phase is known.

Analysis software

• Haploview
• LdCompare^[5] — open-source software for calculating LD.
• PyPop
• HelixTree - commercial software with interactive LD plot.

References

1. ^ Devlin B., Risch N. (1995). "A Comparison of Linkage Disequilibrium Measures for Fine-Scale Mapping". Genomics 29: 311-322.
2. ^ Robbins, R.B. (1918). "Some applications of mathematics to breeding problems III". Genetics 3: 375-389.
3. ^ R.C. Lewontin and K. Kojima (1960). "The evolutionary dynamics of complex polymorphisms.". Evolution 14: 458-472.
4. ^ P.W. Hedrick and S. Kumar (2001). "Mutation and linkage disequilibrium in human mtDNA". Eur. J. Hum. Genet. 9: 969-972.
5. ^ Hao K., Di X., Cawley S. (2007). "LdCompare: rapid computation of single- and multiple-marker r2 and genetic coverage". Bioinformatics 23: 252-254.

See also

• Hardy-Weinberg principle
• Genetic linkage
• Co-adaptation
• Genealogical DNA test
• Tag SNP

Further reading

• Hedrick, Philip W. (2005). Genetics of Populations, 3rd, Sudbury, Boston, Toronto, London, Singapore: Jones and Bartlett Publishers. ISBN 0763747726.